Production program
Die-casting machines
TL6 - 500
Die-casting machines TL5,6 - xxx (250, 400, 500, 630, 750) with horizontal cold chamber are designed for casting of parts under pressure. The parts can be out of aluminium, magnesium, zinc or copper alloys. These machines can be used especially for seriál and mass production. With their electro equipment can be used in workingplaces too.
- TL5,6 - 250
- TL5,6 - 400
- TL5,6 - 500
- TL5,6 - 630
- TL5,6 - 750
 | TL 5 and TL 6 PRESSURE DIE-CASTING MACHINES |
Automatized workingplace of die-casting
Automatized workingplace of die-casting
| Automatized workingplace of die-casting |
Automatized workingplace of die-casting (AW) is designed for partial or fully automated working cycle according to customer´s demand. AW is controlled by the central control systém, which is a part of the machine´s control system. Thanks to that is possible to control all AW devices from one place.
The basic parts of automatized workingplace:
- DIE-CASTING MACHINE TL5,6 - XXX
- METAL DOSER
- FURNACE
- ROBOT WITH PERIPHERIALS
Is possible to use every robot, which corresponds with terms of use in mouldry. The robot must have sufficient maximal load and reach level of hand. - TEMPERATION OF FORM
- TRIMMING PRESS
- ROTATING CONVEYOR FOR TRANSPORT BOXES
- STEP-PHASED CONVEYOR
- POWER-BRIDGE AND THE MAIN AW SWITCHBOARD
Working place for casting of rotors
Machine for casting of rotors STLR-400
This is a workingplace, which is designed for production of aluminium rotors (AL 99,5% alloy) with axial height of 180 - 225 mm. Main dimensions of workingplace are 18500 x 7300 mm. Workingplace is designed for two workers.
Workingplace consists of:
- Packing press
- Die-casting machine
- Shaft press
- Smelting and holding furnace (Gas)
- Dosing furnace with traversing
- Manipulators
- Packages cartridge
- Sheetmetal conveyor
- Cleaning device
- Cooling tunnel
- Cooling device
- Exhausting
- Tempering aggregates
- Conveyor for sprues
- Conveyor for spindles
- Cooling tank
Gravitation casting machines
Tilt-casting machine NLS-1
| Tilting Chill mould Machine PLS 2 x 50 - 2 |
| NLS-1 |
According to experiences with gravitation casting of aluminium alloys into the steel form were known, that within a casting of some mouldings is good to change position of form from vertical to horizontal. This casting style will really bring lower poresity and the spoils production. In purpose of that have we designed workingplaces of chill casting with closing power of 500 kN type PLS 2x50-2 and NLS-1 whose ensure these technology.
Workingplace consists of:
- Two tilting machines with closing power of 500 kN
- Aggregate like the source of pressure fluid
- Electronic box
- Two control boxes
- Two foot steppers for starting of the machine
Trimming hydraulic presses
Trimming press OL 28
Trimming hydraulic presses with trimming force of 1570, 2800 or 5120 kN whose are designed for removing of frays on pressure mouldings or complete sets with sprues. Removing should be made with help of cutting, perforating in combination with cushioned parts.
- OL 15-2
- OL 28-2
- OL 28-3
- OL 50-2
- OL 50-3
Presses for ceramic materials
CJC - 100 press for pressing of ceramics
| Hydraulic Press - CJC 100 |
| Hydraulic Press - CJC 140 |
| Hydraulic Press - CJC 160 |
Hydraulic presses CJC are designed for pressing of ceramic mouldings, whose are after pressing burned in furnace. CJC presses are produced with clamping force of 1000, 1400, 1600 kN and can be delivered separately or like a part of a workingplace. To those machines can be supplied mixing device, charging equipment, extracting manipulator, cleaning manipulator and conveyors too.
- Hydraulic Press - CJC 100
- Hydraulic Press - CJC 140
- Hydraulic Press - CJC 160
Presses for rubber
Press for rubber DU450
Hydraulic presses for rubber are constructed in vertical or horisontal design with closing force from 600kN. The mouldings are made by injection.
We are able to offer hydraulic vulcanisation presses constructed in vertical construction with closing force from 600 kN where technology of compressive pressing is used.
CBA presses
Hydraulický poloautomatický lis CBA 200
| Semi – automatic Hydraulic Press CBA 100, 160, 300 |
| Semi – automatic Hydraulic Press CBA 500/80 |
CBA presses with closing power between 1600 - 5000 kN are designed for pressing of thermosets (bakelite, carbamate, melamine, rubber) and for use of other technologies. For example pressing of powder (chamotte), pressing of brake relinings, pressing of abrasive wheels. These machines can be used for forming, bending, cutting, mounting works (manual or automatic) too.
- CBA 100
- CBA 160
- CBA 200
- CBA 500
Mounting and Workshop presses
Workshop presses
For use in mounting and unmounting operations. For example inforcing of bushings, pins and bearings, within leveling of rods, bending, perforating etc.
The machines are disparted into those main sections (according to frame type):
- CDCR 8 - 28 with closing power of 80 - 280 kN
4 dimensions, "C" frame, with adjustable width of the table - CDMR 8 - 200 with closing power of 80 - 200O kN
8 dimensions, closed "C" frame with adjustable crossbeams - CDSR 8 - 28 with closing power of 80 - 280 kN
4 dimensions, Table press with firm closed frame
Special presses
Press for glass
Are produced and designed according to customer´s requests:
- Presses for production of flammable and explosive products
- Press for lead cables
- Device for testing and repairing of the form
- Device for inserting of the bigger forms into the presses
- Presses for recycling of plastic materials
- Adapters, like the addictive device for high-density presses for casting of structural materials
Overhauls and
Modernisation of CS1025
Overhauls and modernisations can be made on followings:
- die-casting machines CLH, TL and others produced in TOS Rakovnik
- injecting presses CS, CSY and others produced in TOS Rakovnik
- after discussion are we ready to repair machines which were produced in another works
©Copyright Rakovnicke tvareci stroje s.r.o. 2010
last update: 5th August 2010